Skip to content

Hot tub start-up

How to start up a new or refilled hot tub

Fill the tub, treat the fill water for metals, balance alkalinity then pH then calcium, then add your system’s start-up products in the label’s order. Test before anyone gets in: the sanitizer has to read in range first.

From Sirona’s own directions and labels, checked on 2026-11-15. Where each part comes from

Before the sanitizer — every system

These three steps are the same whichever sanitizer the tub runs on.

  1. Protect the shell and fill the tub

    Wipe the empty shell clean. Sirona’s guide protects an acrylic or fiberglass finish before any water goes in. Let the hose run for several minutes before it goes in the tub, then fill to half way up the skimmer.

  2. Treat the fill water for metals

    Metals in fill water stain the shell once a sanitizer goes in, so this comes before it. The metal treatment goes in as the tub fills, and each system has its own.

  3. Balance the water: alkalinity, then pH, then calcium

    Test the water. Bring total alkalinity into 80–120 ppm first, because it is what holds pH still; then pH toward 7.4–7.6; then calcium hardness into 150–250 ppm. The labels dose only when alkalinity is under 80 ppm, pH is under 7.2 or over 7.8, or calcium is under 150 ppm, so a reading a little off its target is left alone. Wait 15 minutes with the jets on between one product and the next, and retest 3 hours after a pH or alkalinity dose.

Open the system your tub runs on.

Bromine tubs only

Start a bromine tub

Bromine tablets keep a level up; they cannot start one. The order below is the label’s.

  1. Build the bromide reserve

    Sodium bromide goes in first, once per fill, with the water circulating. It is what the tub makes its bromine from, and it is why a freshly filled tub reads nothing however many tablets are in the floater.

  2. Fill the floater

    Put the tablets in a floater and float it. Open or close the floater by what the test strip reads over the next days.

  3. Shock to activate it

    A shock turns the bromide in the water into working bromine and burns off what the fill carried in. Add it with the jets running and leave the cover off for 15 minutes.

  4. Test before anyone gets in

    Bromine should read 3–5 ppm and pH 7.4–7.6. Nobody gets in above 8 ppm of bromine: the label prohibits it.

  5. No floater? The two-part way

    Sirona also makes a two-part bromine system: a bromide salt and the same shock, with no tablets and no floater. The salt goes in first, then the shock, each by its own label.

Chlorine tubs only

Start a chlorine tub

Chlorine works best with pH in range, so the balancing above matters most on this system.

  1. Add the chlorinating granules

    With the water circulating, add the granules, wait a few minutes and test. The label repeats the same amount until free chlorine reads 2–3 ppm.

  2. Shock the water

    Once the water is balanced and sanitized, shock it to burn off what the fill carried in. Jets running, cover off for 15 minutes.

  3. Test before anyone gets in

    Free chlorine should read 2–4 ppm and pH 7.4–7.6. Nobody gets in above 5 ppm of free chlorine: the label prohibits it.

Simply tubs only

Start a Simply tub

Simply is Sirona’s chlorine-free, bromine-free system: three liquids, added in order. Nothing with chlorine or bromine in it ever goes in this water.

  1. Step one: Waterline Control

    Shake the bottle and add it to the full tub. It keeps deposits from forming at the waterline.

  2. Step two: Simply Oxidizer

    Add the oxidizer, then circulate for at least 15 minutes on high speed.

  3. Step three: Simply Sanitizer

    Add the sanitizer and circulate again for 15 minutes.

  4. Test with Simply strips

    A Simply tub is read on Simply test strips; a chlorine and bromine strip cannot read it. The sanitizer should read 30–50 ppm, and it should never fall under the lower number.

What not to do

  • Never add chemicals to the water when people are in the spa.
  • NEVER mix chlorine and acid (or any two chemicals) together — toxic chlorine gas. Add each chemical to the water separately, circulating between additions
  • Never add chlorine, bromine, a chlorine-based shock or a mineral cartridge to a Simply tub: Sirona says the Simply products are compatible only with the Simply system.
  • Nobody gets in above 5 ppm of free chlorine or 8 ppm of bromine: the labels prohibit it.
  • Never heat the tub above 104°F.

Free water testing at the store

Bring a sample. Leave with a plan for your tub.

A test strip is a rough read. At the counter we test the water and print a plan made for a hot tub, not a pool: each reading against its target, and what to add in the order to add it.

  • Sized to your tub’s gallons, so bring the number with the sample.
  • Every amount is taken from the product’s own label. A product whose label rate we have not read is named without an amount, never guessed.
  • For bromine, chlorine or Simply. A Simply tub is never told to add chlorine or bromine.

Where

Simplified Pools

1611 Commons Cir Suite 100, Northlake, TX 76226

(469) 455-1054

  • Monday – Friday10am – 6pm
  • Saturday10am – 3pm
  • SundayClosed

No appointment is needed for a water test.

Questions people ask next

Do I need to add anything before the sanitizer?

Yes. Treat the fill water for metals and bring alkalinity, pH and calcium into range first. A sanitizer added to unbalanced water does not hold, and one added to water with metals in it can stain the shell.

Why does a newly filled bromine hot tub read zero?

Because tablets alone cannot build the bromide reserve the water makes its bromine from. Add sodium bromide once per fill and shock to activate it, and the tablets will then keep the level up.

How soon can I get in after starting up a hot tub?

When the sanitizer tests in range and under the label’s limit: no more than 5 ppm of free chlorine or 8 ppm of bromine. Test first, every time.

Can I start a tub on Simply after it has had chlorine or bromine in it?

Only on fresh water. Sirona says the Simply products are compatible only with the Simply system, so the change is made at a drain and refill.

Where this comes from

Every step and every rate on this page is Sirona’s own, read on 2026-11-15. Always read the label on the bottle in your hand: it is the one that counts.

Free checklist

The DFW month-by-month pool checklist

What it covers (12 months · 76 tasks · 12 marked critical):

  • Freeze nights (January and December): keep the pump running, and what to drain if the power goes out
  • The March opening: test everything, brush, shock, then balance alkalinity, pH and calcium
  • Summer: testing two or three times a week, the weekly shock, and what to do after rain or a party
  • Fall leaves, and easing the chemistry down for winter
Read it now — no email needed →

Email me the checklist

One email with a link to the printable checklist — print it, or save it as a PDF, from that page. That is all we send: no mailing list.

Retail Store

Visit Us Today

Stop by for free water testing, expert advice, and professional-grade supplies.

Simplified Pools

1611 Commons Cir Suite 100
Northlake, TX 76226

Get Directions →
Call Now
Book Service