Skip to content
SIMPLIFIEDPOOLS

Harvest, TX · 76226 · 76247

Pool Automation Repair in Harvest, TX

Diagnostic and field repair for Pentair, Hayward, and Jandy automation panels, wireless links, and actuators. Most relay and sensor faults resolve in a single visit. Book an on-site diagnostic online or call to schedule service.

⚡ Same-day when parts on truck
Book a diagnostic visit · $125 →Call (469) 455-1054

What our pool automation repair covers in Harvest

On-site troubleshooting and component-level repair for computerized pool control systems. Techs test high-voltage relays, low-voltage RS-485 communication loops, motorized valve actuators, and mobile-link gateways to get scheduled filtration, heating, and lighting running reliably again.

  • ✓Pentair IntelliCenter, EasyTouch, and IntelliTouch motherboards, screen assemblies, and firmware
  • ✓Hayward OmniLogic, OmniHub, and ProLogic main boards, expansion boards, and local display panels
  • ✓Jandy AquaLink RS, PDA, and iAquaLink 2.0 / 3.0 web-connect interfaces and power centers
  • ✓Motorized valve actuators (Jandy Pro-Line, Pentair CVA-24, Hayward GVA-24) and cam switch adjustments
  • ✓High-voltage relays (3HP / 24V coil) for auxiliary pumps, blowers, and landscape lighting circuits
  • ✓Water, solar, and air temperature sensors (10k ohm thermistors) and calibration
  • ✓RS-485 comm wiring diagnostics between variable-speed pumps, salt cells, and main control boards
  • ✓Antenna extensions, wireless transceivers, and direct Ethernet-over-powerline bridge modules

What we don't do (just so you know)

  • • Home network overhauls — we verify and configure the pool gateway to your 2.4GHz network, but we do not reconfigure whole-home mesh routers or ISP firewalls
  • • Warranty-covered claims — we diagnose the failure, document the serials and fault logs, and point you directly to the manufacturer warranty intake (free of charge)
  • • Underground conduit trenching or pulling new main line high-voltage feed wires from the home subpanel

Common pool automation repair problems in Harvest

Tap the one you’re seeing to book a visit — most are found and fixed in one trip.

iAquaLink, OmniLogic, or ScreenLogic app shows "device offline" or fails to syncValve actuator stuck in spa mode or fails to turn when switching to spilloverControl panel reads 0°F, 140°F, or "sensor open" error, preventing the heater from firingPump or heater will not start on its programmed schedule despite relays clickingIntelliCenter or Omni display screen is blank, frozen, or unresponsive to touchAutomation loses time and schedule settings every time power trips

Everything on the pad

What we fix

PumpsFiltersHeatersSalt cellsLeaksAutomation

In stock at our store

Pool equipment parts we carry

Doing it yourself? Order online or pick up in Northlake. Want it done? These ride on our trucks.

All parts →
PENTAIR Black Seal Plate Gasket

PENTAIR

PENTAIR Black Seal Plate Gasket

$9.99In stock
Angel Skimmer Basket Handle

Poolstyle

Angel Skimmer Basket Handle

$15.45In stock
HAYWARD Hayward Diffuser O-Ring

Hayward

HAYWARD Hayward Diffuser O-Ring

$24.99In stock
WHISPERFLO STRAINER BASKET

VAL-PAK

WHISPERFLO STRAINER BASKET

$27.86In stock
Black Valve Knob Replacement Kit for NeverLube® Diverter Valve

Jandy

Black Valve Knob Replacement Kit for NeverLube® Diverter Valve

$29.49In stock
WEIR BLADE 8-3/8" STA RITE U3

PWP

WEIR BLADE 8-3/8" STA RITE U3

$33.99In stock
35MFD 370V ROUND RUN CAPACITOR

Super-Pro

35MFD 370V ROUND RUN CAPACITOR

$36.49In stock
8 3/8" Lens Gasket for Amerlite Incandescent Underwater Pool Lights

PENTAIR

8 3/8" Lens Gasket for Amerlite Incandescent Underwater Pool Lights

$40.43In stock

About pool automation repair in Harvest, TX

Harvest is a globally recognized "agrihood" master-planned community that anchors the growth between Northlake and Argyle. Built around a working farm, a community lake, and massive lifestyle amenities, Harvest attracts families who are highly engaged in their property upkeep. Because we are headquartered right next door in Northlake, we are essentially the "hometown" pool service for Harvest residents. The pools in this community are predominantly newer, family-centric designs featuring tanning ledges, sheer descents, and cartridge filtration systems.

Harvest water profile

Municipal water supply yielding relatively soft, balanced water. The primary maintenance challenge in Harvest stems from the high density of new construction dust in the newer phases and the heavy bather load common with young families.

Harvest pool & equipment mix

Family-friendly designs, heavily leaning toward modern rectangular shapes, integrated spas, and salt water sanitation.

Neighborhoods we serve in Harvest

Harvest TownsideHarvest MeadowsHarvest WestThe Back Porch

Working pool automation repair jobs near…

Harvest FarmHarvest LakeThe Farmhouse CoffeeArgyle West Elementary
"We brought Simplified Pools on after our builder's pool company stopped showing up. They balanced the water perfectly and the salt cell is finally working right."
— Mark T., Harvest Resident

Other things we handle in Harvest

Service

Pool Repair

Service

Pentair Repair

Service

Jandy Repair

Service

Hayward Repair

How a repair visit goes

  1. Step 1

    Book or call

    Pick a day online, or call and tell us what the pad is doing.

  2. Step 2

    We find the cause

    A flat $125 diagnostic — waived when we do the repair that visit.

  3. Step 3

    You approve the price

    You see the fix and the price before any work starts.

  4. Step 4

    Fixed and tested

    Common parts ride on the truck, so most jobs finish the same visit.

Book a diagnostic visit · $125 (469) 455-1054

Who shows up

Our own technicians

  • Parts on the truck

    Same-day when we carry your part.

  • Licensed and insured

    And the repair work is warrantied.

  • Every major brand

    Pentair, Hayward, Jandy, Sta-Rite and more.

Harvest pool automation repair questions

How fast can you get to my Harvest pool for pool automation repair?
Same-day visits are common in Harvest when we have parts on the truck — call (469) 455-1054 before 11 AM and we usually have someone out the same afternoon. We run daily routes through Denton County, including Argyle and Northlake, so windshield time is rarely what holds a Harvest job up. After hours, next morning at the latest.
Does Harvest water affect pool automation repair?
Harvest is on municipal water (typically Upper Trinity Water District or DCUD), which is relatively clean — TDS under 500 ppm — but summer irrigation demand and Texas heat still push chemistry around. For pool automation repair that's mostly good news — the failures we see in Harvest are heat-cycle and chemistry-drift related rather than mineral, so they're more predictable and cheaper to stay ahead of. Many Harvest pools run salt chlorine generators, which changes how we dose the other chemicals.
Do you charge for the diagnostic visit even if I don't book the repair?
Yes — there's a flat diagnostic charge that we quote on the call before we send a tech. We waive it if you book the repair on the same visit. The diagnostic includes a written estimate so you can compare or get a second opinion before any work starts. We don't publish a fixed repair price online because every job is genuinely different — but you'll never get a surprise number.
Are you licensed and insured for pool work in Harvest?
Yes — we carry full general liability + workers' comp, and our techs are trained on every major brand (Pentair, Hayward, Jandy, Sta-Rite). We're a real local business in Argyle serving Harvest (76226, 76247), not a referral marketplace that sells your details to whoever answers first.
Do you bring parts on the first visit, or do I wait for a second visit for the repair?
We stock the most-common parts on every truck — pump seals, basket lids, cartridges, sand, filter o-rings, ignition components, salt-cell test kits. About 70% of repairs in Harvest finish on the first visit. The other 30% need a part order; we book the return for the next available slot, usually within 48 hours.
Why is my pool automation app showing offline when my home Wi-Fi works fine?
Most pool automation transceivers communicate strictly on 2.4 GHz Wi-Fi bands. Metal equipment enclosures, brick exteriors, and dual-band routers that force devices toward 5 GHz frequently drop the signal. Failed wireless antennas, loose RS-485 comm wiring between the board and transceiver, or outdated bridge firmware are the most common hardware culprits.
Can you repair an older pool panel or do I have to upgrade to a brand-new system?
We repair legacy panels like Pentair EasyTouch, Jandy AquaLink RS with older chipsets, and Hayward ProLogic whenever replacement boards, relays, or modern upgrade kits (such as iAquaLink or OmniHub conversion kits) are practical and cost-effective. We only recommend a panel upgrade when the circuit board is obsolete or the cost of individual replacement parts approaches a modern upgrade kit.
Why is my heater not turning on through my automated panel?
Automation systems control heaters via a low-voltage "fireman's switch" loop or RS-485 digital comm line. If the water temperature sensor fails (often reading an extreme value), the automation board will not close the call-for-heat circuit. We test the thermistor resistance, the heater relay on the board, and the physical communication line to isolate the failure.
What causes a valve actuator to stop turning?
Actuator failures usually stem from a failed internal microswitch, a stripped drive gear, worn internal seals that let moisture into the 24V motor, or a blown auxiliary fuse on the automation board. We carry replacement actuators and internal switch assemblies to resolve these on the visit.

Harvest pool automation repair — call (469) 455-1054

Family-owned in Argyle. Real techs, real same-day service when we have parts on the truck.

Book a diagnostic visit(469) 455-1054

Free checklist

The DFW month-by-month pool checklist

What it covers (12 months · 76 tasks · 12 marked critical):

  • Freeze nights (January and December): keep the pump running, and what to drain if the power goes out
  • The March opening: test everything, brush, shock, then balance alkalinity, pH and calcium
  • Summer: testing two or three times a week, the weekly shock, and what to do after rain or a party
  • Fall leaves, and easing the chemistry down for winter
Read it now — no email needed →

Email me the checklist

One email with a link to the printable checklist — print it, or save it as a PDF, from that page. That is all we send: no mailing list.

Retail Store

Visit Us Today

Stop by for free water testing, expert advice, and professional-grade supplies.

Simplified Pools

1611 Commons Cir Suite 100, Northlake, TX 76226
Northlake, TX 76226

Get Directions →
Call Now
Book Service